OS/2 DEVICE DRIVER FOR THE CIRRUS LOGIC 5430, 5434 ************* *** NOTE: MUST INSTALL STANDARD VGA BEFORE INSTALLING THESE DRIVERS! *** Install procedures are on page 4 of this document. *** *** If this file was download, the physical install disk must have a *** volume label of "CIRRUS 1" without the quotes. ************* This package contains the following: o An OS/2* graphics device driver supporting the 5430, 5434 chip set from Cirrus Logic**, Inc. o This README file, which is formatted for viewing on your screen. You can: - Use the Table of Contents to help you locate specific topics. - Use the Find option in the Edit menu of the OS/2 System Editor to help you locate specific information. - Print the file. IMPORTANT PLEASE READ THE FOLLOWING TERMS AND CONDITIONS. YOUR USE OF THE OS/2 DEVICE DRIVER FOR THE CIRRUS LOGIC 5430, 5434 INDICATES YOUR ACCEPTANCE OF THE FOLLOWING TERMS AND CONDITIONS: o YOU MUST BE, AND YOU AGREE THAT YOU ARE, A PRIOR LICENSEE OF OS/2. o YOU MAY MAKE COPIES OF THE OS/2 DEVICE DRIVER FOR THE CIRRUS LOGIC 5430, 5434 EQUAL TO THE NUMBER OF LICENSED COPIES OF OS/2 YOU POSSESS. o ALL OTHER TERMS AND CONDITIONS OF YOUR OS/2 LICENSE AGREEMENT APPLY TO THIS OS/2 DEVICE DRIVER FOR THE CIRRUS LOGIC 5430, 5434; HOWEVER, THIS DOES NOT EXTEND ANY WARRANTY OUTLINED IN SUCH AGREEMENT. CONTENTS ________ 1.0 Supported Features 1.1 Supported Resolutions 1.2 Supported Adapters 1.3 Supported Columns and Rows 2.0 Compatibility 3.0 Preliminary Steps 4.0 Installation from Diskette 5.0 Installation in a CID Environment 6.0 Functional Restrictions 7.0 Setting Your Display to VGA Mode 8.0 APARs Included in This Driver 9.0 Trademarks 1.0 SUPPORTED FEATURES __________________ The Cirrus Logic 5430, 5434 device driver provides seamless support for accelerated display graphics and advanced color resolutions when used with the minimum required video memory. It conforms to the OS/2 32-bit flat memory model and is designed to function as a 32-bit Presentation Manager* graphics display driver under the OS/2 32-bit graphics engine. This driver has been enabled for use with the IBM* Distributed Console Access Facility (DCAF) product. 1.1 SUPPORTED RESOLUTIONS This video accelerator driver supports these resolutions and color depths: Number of Video Memory Resolutions Colors Required 640x480 256 1MB 800x600 256 1MB 1024x768 256 1MB 1280x1024 256 2MB 640x480 65,536 1MB 800x600 65,536 1MB 1024x768 65,536 2MB 1280x1024 65,536 4MB 640x480 16,777,216 2MB 1.2 SUPPORTED ADAPTERS IBM has tested the listed display adapters and systems containing the Cirrus Logic 5430, 5434 chip set with the specified amount of memory. IBM is continuing to test; therefore, support for additional cards might be added over time. IBM Aptiva 310, 330, 350, 510, 530, 535, 710, 730 Models 2144 and 2168 at service level C1/C2. IBM PS/2 9553 IBM PC 330 9571 PC 350 6581 For a comprehensive listing of all major manufacturing products that are OS/2 compatible, Refer to the "OS/2 Hardware Compatibility List" book. This book is available electronically on the following Bulletin Board Systems: IBM National Support Center BBS (data connection: 919-517-0001) CompuServe (IBM OS/2 Support Forum \Library\IBMFiles\PCMTABLE.ZIP) Prodigy LAN Server & OS/2 BBS -Sydney Australia IBM Austria BBS - Vienna, Austria IBM BBS - Vancouver, BC, Canada IBM PS BBS - Hong Kong IBM OS/2 BBS & IBM AP OS/2 BBS - Singapore IBM BBS - Belgium IBM BBS - England IBM BBS - Spain OS2BBS - Denmark Hitline BBS- Switzerland DAP & PSP BBS - Italy IBM BBS - Jakarta IBM BBS - Thailand NOTE: The compatibility hardware test information supplied is provided for information purposes. IBM makes no warranty, express or implied, with respect to the operation of OS/2 on the personal computers listed. 1.3 SUPPORTED COLUMNS AND ROWS This Cirrus Logic 5430, 5434 device driver supports the following number of columns and rows in an OS/2 full-screen session: Columns Rows 132 25 132 43 2.0 COMPATIBILITY _____________ This graphics accelerator driver is compatible with OS/2 2.1, 2.11, and OS/2 Warp 3. 3.0 PRELIMINARY STEPS _________________ The following steps prepare your computer for the Cirrus Logic device driver: 1. You must have OS/2 DOS Support installed in order to install this driver. 2. If you previously installed SVGA support, return to VGA resolution using the procedures in "Setting Your Display to VGA Mode" later in this README before you install this driver. 4.0 INSTALLATION FROM DISKETTE __________________________ To install the Cirrus Logic device driver from diskette, do the following: 1. Insert the Cirrus Logic diskette into drive A (or any other diskette drive). 2. Open an OS/2 full-screen or OS/2 window session. 3. At the OS/2 command prompt, type the following command to copy all necessary files to the OS/2 drive: A:SETUP A: C: (where A: is the diskette drive, and C: is the drive where OS/2 is installed.) Then press Enter. 4. When prompted to do so, remove the diskette from drive A, perform a shutdown, and then restart your computer. 5. Open the OS/2 System folder. 6. Open the System Setup folder. 7. Open the Display Driver Install object. When the Display Driver Install window appears, select Primary Display Driver and then select OK. 8. When the Display Driver Select window appears, select "Cirrus Logic 5430, 5434 (IBM BBS)" to install the BBS video driver. 9. When the Monitor Configuration/Selection Utility window appears, the "Install Using Defaults for Monitor Type" choice is preselected. You can accept this choice or select "Install Using Display Adapter Utility Program" to choose a different refresh rate. Then select OK. If you select the "Install Using Display Adapter Utility Program" choice, you must have a DOS monitor utility that came with your display adapter. Contact the display adapter manufacturer's technical support for information on how to use the monitor utility under OS/2. NOTE: At this point, DSPINSTL determines the hardware configuration by creating the \OS2\SVGADATA.PMI file. If the \OS2\SVGADATA.PMI file has not been created, the adapter will not be supported. This process can take several seconds and will black-out the screen. 10. When the Source Directory pop-up window appears, insert the Cirrus Logic diskette into drive A. Then select Install. 11. When the installation is complete, do the following: a. Open the OS/2 System folder. b. Open the System Setup folder. c. Open the System object. d. When the Settings notebook appears, select the Screen tab. Then go to Screen page 2. e. On Screen page 2, select your display from the display list. If your display does not appear in the list, select Default. f. Return to Screen page 1 and select a screen resolution and a screen refresh rate. g. Close the Settings notebook. h. Perform a shutdown and restart your computer. Note that during the installation of this driver, DISPLAY.LOG and DSPINSTL.LOG files are created in the OS2\INSTALL directory. These files identify the OS/2 system files that were updated and indicate whether the installation was successful. The contents of these files might be useful if you need to report an installation problem to IBM. 5.0 INSTALLATION IN A CID ENVIRONMENT _________________________________ NOTES: 1. The server must contain a directory named CIR_DRVS on the same drive where the OS/2 diskettes reside. The CIR_DRVS directory must contain all of the files from the Cirrus Logic device driver diskette. 2. OS/2 must have been successfully installed on the client using the CID (Configuration Installation Distribution) method. To install the Cirrus Logic device driver using CID, use the following information to modify your LCU command file. NOTE: The following information is meant as a guide. Your LCU command file might be different. /*****************************************************/ /* LCU PRODUCT DATA SECTION */ /*****************************************************/ . . . x.cirvideo = 15 x.15.name='Cirrus Video' x.15.statevar = 'CAS_' || x.15.name x.15.instprog = 'x:\img\cir_drvs\SETUP.CMD', ' x:\img\cir_drvs ' || bootdrive || ' CID' x.15.rspdir = '' x.15.default = '' x.cirdspinstl = 16 x.16.name='Cirrus CID Dspinstl' x.16.statevar = 'CAS_' || x.16.name x.16.instprog = bootdrive || '\os2\install\DSPINSTL.EXE', ' /pd:' || bootdrive || '\os2\install\cl54xbb.dsc', ' /s:x:\img\cir_drvs', ' /t:' || bootdrive, ' /res:640x480x256', ' /u' x.16.rspdir = '' x.16.default = '' /*---------------------------------------------------*/ /* NUMBER OF PROGRAMS SET UP IN THE */ /* PRODUCT DATA SECTION */ /*---------------------------------------------------*/ NUM_INSTALL_PROGS = 16 /*****************************************************/ /* INSTALLATION SECTION */ /*****************************************************/ . . . when OVERALL_STATE = 2 then do if RunInstall(x.cirvideo) == BAD_RC then exit Call RebootAndGotoState(3) end when OVERALL_STATE = 3 then do if RunInstall(x.cirdspinstl) == BAD_RC then exit Call CheckBoot end . . . /******************************************************/ /* ROUTINE SECTION */ /* The following information should already exist in */ /* the LCU command file. */ /******************************************************/ . . . RebootAndGotoState: parse arg new_state, other rc2 = SetState(new_state, 'RebootAndGotoState', 1) /* Set the state */ /* to go to in */ /* OVERALL_STATE */ Call SaveStates /* Save the environment vars */ Call Reboot /* Reboot the machine */ return . . . /*****************************************************/ END OF LCU INFORMATION TO BE ADDED /*****************************************************/ Following is an explanation of the line that is executed in the LCU command file: C:\OS2\INSTALL\DSPINSTL /pd:c:\os2\install\cl54xbb.dsc /S:X:\img\cir_drvs /T:C: /res:640x480x256 /u /pd:c:\os2\install\cl54xbb.dsc is the dsc laid down during setup phase /S:X:\img\cir_drvs where X:\img\cir_drvs is the redirected source path. /T:C: where C: is the drive where OS/2 is installed. /res:640x480x256 is a resolution/color depth from the list of "Supported Resolutions" that appears earlier in this README. /u Unattended installation. NOTES: 1. Be sure you have the stated video memory required, as listed in "Supported Resolutions" earlier in this README. A safe choice is 640x480x256. Any of the listed resolutions can be selected, but your display might be damaged if you select a resolution that your display does not support. 2. After the CID install, refer the end user to 4.0 INSTALLATION FROM DISKETTE step 11. 6.0 FUNCTIONAL RESTRICTIONS _______________________ o After Dark** for Windows** images that move from left to right do not perform properly at 640x480x16M resolution. o To avoid a general protection fault while loading Ventura Publisher** for Windows, be sure it is in one of the 256 color resolutions. o To avoid a trap in Lotus*** 1-2-3** for OS/2, do not attempt to run the program at 16.7 million colors. o WordPerfect** Versions 5.1 and 5.2 for Windows produce a general protection fault when the "Print Preview" option is selected while using 800x600x64K or 600x480x16 million color mode. o Users of the software motion video feature of MMPM/2* should expect satisfactory results in 256-color modes. However, in 64K-color modes, users of the feature will experience unusual results. An OS/2 pervasive fix package will be available electronically. The software motion video feature is not supported in 16-million color modes. o CorelDRAW** 2.0 will not run in a WIN-OS/2* window session. It must be run in a WIN-OS/2 full-screen session. o Micrografx** Charisma 2.1 will not run in a WIN-OS/2 window session. It must be run in a WIN-OS/2 full-screen session. o Distributed Console Access Facility (DCAF) is supported in 256-color modes only. o You might have to run the CLMODE utility to enable the BIOS to generate high-resolution modes. 7.0 SETTING YOUR DISPLAY TO VGA MODE ________________________________ Use the following procedures to return to VGA mode. o If you are installing this driver on OS/2 Warp, and you do not have a usable OS/2 Desktop, use the following procedures to return to VGA mode. However, if you have a usable Desktop, it is recommended that you use Selective Install to set your display to VGA mode. 1. Turn on your computer. If your computer is already on, press Ctrl+Alt+Del to restart it. 2. When a small white box appears in the upper left-hand corner of your screen, press Alt+F1. 3. When the Recovery Choices screen appears, press V. Your display adapter is restored and can work in VGA mode. If you want to install a new display adapter or video device driver, refer to Chapter 16, "Video Procedures," in the User's Guide to OS/2 Warp. o If you are installing this driver on OS/2 2.1, 2.11, or OS/2 for Windows, and you do not have a usable OS/2 Desktop, use the following procedures to return to VGA mode. However, if you have a usable Desktop, it is recommended that you use the Display Driver Install object to set your display to VGA mode. - If you installed OS/2 from diskettes, do the following: 1. Start OS/2 using the OS/2 Installation Diskette. When prompted, insert Diskette 1, and then press F3 to display a command prompt. 2. Be sure RSPDSPI.EXE is in the \OS2\INSTALL directory. If it is, go to step 2. If it is not, insert Diskette 8 into drive A and unpack RSPDSPI.EXE with the following command: C:\OS2\UNPACK A:\INSTAID C: /N:RSPDSPI.EXE (where A: is the drive containing Diskette 8, and C: is the drive where OS/2 is installed.) 3. Type C: and then press Enter. 4. Type CD C:\OS2\INSTALL and then press Enter. 5. Type the following: RSPDSPI /PK:VGA /SK:NONE /S:A:\ /T:C: (In /T:C:, C: is the drive where OS/2 is installed. In /S:A:, A: is the diskette drive you use to install OS/2.) Then press Enter. - If you installed OS/2 from CD-ROM or a LAN, do the following: 1. Start OS/2 from the OS/2 Installation Diskette. When prompted, insert Diskette 1, and then press F3 to display a command prompt. 2. Be sure RSPDSPI.EXE is in the \OS2\INSTALL directory. If it is, go to step 2. If it is not, unpack RSPDSPI.EXE with the following command: C:\OS2\UNPACK E:\DISK_8\INSTAID C: /N:RSPDSPI.EXE (where C: is the drive where OS/2 is installed, and E: is the CD-ROM or LAN drive.) 3. Type C: and then press Enter. 4. Type CD C:\OS2\INSTALL and then press Enter. 5. Type the following: RSPDSPI /PK:VGA /SK:NONE /S:E:\OS2SE21\ /T:C: (In /T:C:, C: is the drive where OS/2 is installed. In /S:E:, E: is the CD-ROM or LAN drive.) Then press Enter. 8.0 APARS INCLUDED IN THIS DRIVER _____________________________ Some fixed APARs may not be listed. If you received this driver through the IBM OS/2 support channel and your requested APAR is not listed, please install the driver, as your requested APAR is included. APAR= PJ16493 WARP,CM/2 1.11,5250 EMULATOR IN ANY SVGA RES UNDERSCORE DISPLAYS OUT OF WINDOW. APAR= PJ18212 DRAG OPEN FOLDERS INSIDE FILE MANAGER (SEAMLESS SESSION) , AND REMNANTS OF THE BORDERS ARE LEFT INSIDE FILE MANAGER. 9.0 TRADEMARKS __________ The following terms, denoted by an asterisk (*) in this file, are trademarks or registered trademarks of IBM Corporation in the United States and/or other countries: IBM MMPM/2 OS/2 Presentation Manager WIN-OS/2 The following terms, denoted by a double asterisk (**) in this file, are trademarks or registered trademarks of other companies as follows: TRADEMARK OWNER After Dark Berkely Systems, Inc. Cirrus Logic Cirrus Logic, Inc. CorelDRAW Corel Corporation Lotus Lotus Development Corporation Micrografx Micrografx Incorporated Ventura Publisher Ventura Software, Inc. Windows Microsoft Corporation WordPerfect WordPerfect Corporation 1-2-3 Lotus Development Corporation IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY RELATED PATENTS OR COPYRIGHTS. THIS DRIVER IS COPYRIGHTED BY INTERNATIONAL BUSINESS MACHINES CORPORATION. ALL APPROPRIATE RESTRICTIONS APPLY. (End of Document)